YSI 5200A Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 139

background image

YSI 5200A
111

YSI 5200A
110

•

Use

▲

▼

to scroll and highlight IOEM channels.

•

Press



to select.

•

Press

to save settings and return to Run Screen.

Notes:

-

The Channel menu displays a generic list of instruments being Channel 1-8.

- The Channel menu will always display Channels 1-8 regardless if the

IOEM device selected is an IOEM-4 which has only 4 channels and not
8.

-

IOEM channel modes can only be configured using AquaManager. See
AquaManager online help for directions to configure IOEM channel input
mode (digital, 0-1V, 0-5V, 4mA-20mA, temperature);

Input Type

Menus → System → Configure E-Aux →E-Aux 1-8→Input Type →Digital

→0-1v

→0-5v

→4/20ma

→Temperature

Select the input type for the device(s) wired to IOEM channel(s). E-Aux Sensor Setup
menu selections are based on the E-Aux input type configured at system>E-Aux
menu. Input types are discussed in the following sections.

E-Aux Digital input type

Menus → System → Configure E-Aux →E-Aux 1-8→Input Type→Digital

Use the digital input when wiring an external device to control or alarm when the
contacts of the external switch are open or close. A common application would be
to detect high or low water levels using a float switch.

Configuring the 5200A

Notes:

-

IOEM input channel modes can only be configured using AquaManager. See
AquaManager online help for directions to configure IOEM channel input
mode (digital, 0-1V, 0-5V, 4mA-20mA, temperature);

-

Suffix, Min, Max, Input Scale Min, Input Scale Max and Display Format are
not available for digital inputs.

-

In the 5200A sensor log, aux digital “closed” is logged as Aux 0.00. Aux digital
“open” is logged as Aux 1.00.

Directions to configure E-Aux Digital - Configure E-Aux System menu:

1. Wire E-Aux digital devices - see IOEM Safety and Installation

Guide>Chapter 3 Installation and Wiring>IOEM input configuration>Wire
digital input.

2. Refer to and follow directions at IOEM Safety and Installation

Guide>Chapter 4>Quick Start - IOEM Configuration to confirm correct
network connectivity;

3. Follow directions in the Quick Start section to configure IOEM channel

mode to digital.

4. Enter E-Aux menu

5.

Menus → System → Configure E-Aux →E-Aux 1-8

6. Use

▲

and

▼

to scroll and select submenus.

7. Press



to select.

8. Configure E-aux system name - page 108, instrument - page 108, chan-

nel - page 109 and input type - page 110.

9. Press

to save configuration and return to Run Screen.

10. Go to Sensor Setup Menus → Sensor Setup E-Aux 1-8 - page 162 to en-

able and configure control/alarm on condition, control/alarm relay, and
hold off time.

11. Press

to save configuration.

Configuring the 5200A

«
...
54
55
56
57
58
...
»

Содержание 5200A












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5200A

ElectraElite IPK

Бренд: NEC Страницы: 20

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Yudian Страницы: 26

Бренд: tams elektronik Страницы: 60

Бренд: Garmin Страницы: 4

Бренд: Harmonic Drive Страницы: 85

Бренд: Oceanic Страницы: 11

MT600iWP Series

Бренд: weintek Страницы: 2

F&G Xcomfort CRCA-00/02

Бренд: Moeller Страницы: 4

Бренд: ShoreStation Страницы: 19

Бренд: Belkin Страницы: 60

Aqua Wireless 8347

Бренд: claber Страницы: 172

Бренд: Wesco Страницы: 20

Wireless Security Keychain Remote

Бренд: Radio Shack Страницы: 2

Бренд: Curtis Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды