manualshive.com logo in svg

YSI 2900 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
YSI 2900 series Скачать руководство пользователя страница 146

145 

 

 

ACTION: 

Empty waste bottle. 

 

SECTION: 

9.2.1 Empty the Waste Bottle 

POSSIBLE CAUSE: 

Bubbles in buffer or calibrator bottle tubing. 

 

ACTION: 

Prime bottle. 

 

SECTION: 

4.10

 

Prime the Fluid System

  

SYMPTOM: 

 

INTERNAL FAILURE: Unable to Calibrate 

POSSIBLE CAUSE: 

Air bubbles in calibrator tubing. 

 

ACTION: 

Prime calibrator bottles. 

 

SECTION: 

4.10

 

Prime the Fluid System

  

POSSIBLE CAUSE: 

Pinched, leaking or disconnected tube. 

 

ACTION: 

Fix or replace tubing. 

 

SECTION: 

9.4.7

 

Pump Tubing Replacement

  

POSSIBLE CAUSE: 

Sipper misaligned. 

 

ACTION: 

Check Sipper alignment. 

 

SECTION: 

4.5 

Align Sipper 

POSSIBLE CAUSE: 

Stir bar not in sample module. 

 

ACTION: 

Install stir bar. 

 

SECTION: 

9.4.1

 

Sample Module Cleaning 

POSSIBLE CAUSE: 

Stir speed too fast or too slow. 

 

ACTION: 

Adjust stir speed. 

 

SECTION: 

7.2.4

 

Stirbar

 

POSSIBLE CAUSE: 

Newly installed enzyme membrane. 

 

ACTION: 

Enter probe diagnostics and check probe currents. 

 

SECTION: 

7.2.3 Modules 

POSSIBLE CAUSE: 

Newly installed probe. 

 

ACTION: 

Enter probe diagnostics and check probe currents. 

 

SECTION: 

7.2.3

 

Modules

 

POSSIBLE CAUSE: 

Calibrator solution out of spec: contaminated or installed for more than 30 days. 

 

ACTION: 

Install new calibrator. 

 

SECTION: 

4.8

 

Install Calibrator Solution(s)

 

POSSIBLE CAUSE: 

Net calibration current (PL current) below 5 nA. 

 

ACTION: 

Replace enzyme Membrane and check calibrator solution. 

 

SECTION: 

4.9

 

Install Membranes

 

 
POSSIBLE CAUSE: 

Failing enzyme membrane. 

 

ACTION: 

Perform daily operational checks and replace membrane(s) if necessary. 

 

SECTION: 

5.1 Perform Daily Operational Checks

, 4.9 

Install Membranes and ISEs 

POSSIBLE CAUSE: 

Probe surface fouled. 

 

ACTION: 

Clean probe surface. 

 

SECTION: 

9.4.3

 

Enzyme Probe Cleaning

 

POSSIBLE CAUSE: 

Auxiliary electrode fouled. 

 

ACTION: 

Clean Auxiliary electrode surface (temperature probe) with isopropyl alcohol. 

SYMPTOM: 

 

ERROR: No Fluid Detected 

POSSIBLE CAUSE: 

Low sample level. 

 

ACTION: 

Increase sample level in test tube. 

POSSIBLE CAUSE: 

Sipper Depth set too high at sample station. 

 

ACTION: 

Adjust sipper depth. 

Содержание 2900 series







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды