manualshive.com logo in svg

YSI 2900 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
YSI 2900 series Скачать руководство пользователя страница 129

128 

 

 

 

Figure 9.11 

 

Remove the pump tubing from each pump. 
 

Install Buffer Tubing 

Apply plenty of buffer grease (included with the new buffer pump tubing) to the new buffer pump tubing. Apply the grease 
to the large diameter section of each tubing. Do not apply calibrator pump grease to the buffer pump tubing. 

Insert the new pump tubing around the pump roller assembly and into each buffer pump. Make sure the small white fitting 
with the small diameter tubing is on the left side of pump 1 (bottom for pumps 2 and 3).  

Place a blue pump head cover onto each buffer pump and press until it snaps into place. 

For Buffer Pumps 2 and 3, insert the small diameter tubing through the holes in the manifold. Connect the end of the small 
diameter tubing to the buffer valves as described below. 

Connect Buffer Tubing 

Connect the small diameter tubing from Buffer Pump 1 to the inner channel of the bottom valve. 

Thread the small diameter tubing from Buffer Pump 2 through the inner channel of the three tubing holders and connect it 
to the inner channel of the top valve. 

Thread the small diameter tubing from Buffer Pump 3 through the outer channel of the three tubing holders and connect it 
to the outer channel of the top valve. 

Connect the larger diameter tubing from the top of buffer pumps 2 and 3 to the top fitting of each manifold. 

Connect Buffer bottle tubing marked B2 and B3 to the matching fittings on the opposite side of the manifolds. 

9.4.7.3  Calibrator Pump Tubing 

C1A 

Note that the tubing for C1A is slightly longer than C1B.  

Apply plenty of calibrator grease (included with the new calibrator pump tubing) to the longer section of new calibrator 
pump tubing. Do not apply this calibrator pump grease to the buffer pump tubing. 

Insert the new pump tubing around the pump roller assembly and into calibrator pump C1A. Make sure the short section 
of tubing is on the left side of the pump. The tubing attached to this fitting connects to the left fitting on waste module 1. 

Place a red pump head cover onto the cal pump and press until it snaps into place. 

C1B 

Apply plenty of grease (included with the new pump tubing) to the shorter section of new calibrator pump tubing. 

Insert the new pump tubing around the pump roller assembly and into calibrator pump C1B. Make sure the short section 
of tubing is on the left side of the pump. The tubing attached this fitting connects to the right fitting on waste module 1. 

Place a red pump head cover onto the cal pump and press until it snaps into place. 

Содержание 2900 series







































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды