York YCIV Series Скачать руководство пользователя

Страница: 274 / 326

JOHNSON CONTROLS

274

FORM 201.23-NM2

ISSUE DATE: 09/25/2020

SECTION 8 - MICROPANEL

LD10605

SERVICE

KEY

SERVICE KEY

Service Key Operation

The SERVICE key allows viewing data related to the

internal function of the chiller system electronics. Data

such as circuit board output status as controlled by the

Chiller Control software while operating can be viewed

and compared to actual chiller operation in the event

servicing is required. The SERVICE key allows con-

trolling of analog and digital outputs for troubleshoot-

ing purposes when the unit is not running. The Unit

Serial Number and Optimized IPLV Control mode are

also entered using the SERVICE key.
The

▲▼

(ARROW) keys allow scrolling through the

displays. The

▼

(ARROW) key scrolls through the

displays in the forward direction.
When the SERVICE key is pressed, the following mes-

sage will appear:

SERVICE MODE XXXX

PRESS ENTER KEY TO CONTINUE

XXXX will display a password, if a numerical pass-

word is entered.

Pressing the



(ENTER) key allows “view only” Ser-

vice Mode operation. All control board I/O will be

viewable in this mode. No outputs can be changed. For

troubleshooting or start-up commissioning purposes,

the Chiller Micro Board and some VSD outputs can be

toggled or changed by turning off the UNIT SWITCH,

pressing the SERVICE key, entering password 9675,

and pressing the



(ENTER) key. Once the password

is entered, the Digital Outputs (DO) can be toggled by

pressing the



(ENTER) key. The Analog Outputs can

be programmed to output a specific value using the

keypad and programming in the desired value, which

will usually be noted as a % or VDC. If the UNIT

SWITCH is turned back on, the chiller will revert to

normal viewable only control.
Displays can be viewed by pressing the

▲

and

▼

(AR-

ROW) keys. The

▼

(ARROW) key scrolls through the

displays in the forward direction.
The

◄

and

►

(ARROW) keys allow jumping from

data section to data section to avoid scrolling sequen-

tially through all the data. Once in a data section, the

▲

and

▼

(ARROW) keys allow scrolling through the

data under the section. Pressing the

◄

and

►

(AR-

ROW) keys at any time moves to the top of the next

data section.

Содержание YCIV Series







































































































































































































































































































































Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды

York YCIV Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды