York YCIV Series Скачать руководство пользователя

Страница: 264 / 326

JOHNSON CONTROLS

264

FORM 201.23-NM2

ISSUE DATE: 09/25/2020

SECTION 8 - MICROPANEL

Local / Remote Control Mode Selection

Local or Remote Control Mode allows the user to se-

lect the chilled liquid temperature control mode.

OPTIONS LOCAL / REMOTE CONTROL MODE

◄ ► XXXXXXXXXXXXXXXXXX

When LOCAL CONTROL mode is selected, chilled

liquid control is from the keypad of the chiller. In local

mode, a remote device can read system data, but not

reset operating parameters.

OPTIONS LOCAL / REMOTE CONTROL MODE

◄ ► LOCAL CONTROL

When REMOTE CONTROL mode is selected, control

of the chilled liquid setpoint is from a remote device

such as an ISN/BAS controller.

OPTIONS LOCAL / REMOTE CONTROL MODE

◄ ► REMOTE CONTROL

The default mode will be LOCAL.

Display Units Selection

Imperial or SI display units may be selected for data

display.

OPTIONS DISPLAY UNITS

◄ ► XXXXXXXXXXXXXXXXXX

The user may select system operating temperatures and

pressures to be displayed in either SI (°C, Barg) or Im-

perial units (°F, PSIG).

OPTIONS DISPLAY UNITS

◄ ►

IMPERIAL

OPTIONS DISPLAY UNITS

◄ ► SI

The default mode is IMPERIAL.

System Lead/Lag Control Mode Selection

The operator may select the type of lead/lag control

desired.

OPTIONS LEAD / LAG CONTROL MODE

◄ ► XXXXXXXXXXXXXXXXXX

In most cases, automatic lead/lag will be selected.

When automatic lead/lag is selected, the microproces-

sor will attempt to balance run time by switching the

lead compressor whenever all compressors are shut

off. If a compressor is not able to run when the mi-

croprocessor attempts a start, the microprocessor will

select another compressor in an effort to control chilled

liquid temperature. Manual lead/lag allows selecting a

specific compressor to be the lead. If #2 is selected as

the lead in a 3 compressor chiller, the sequence will be

2, 3, and 1.

OPTIONS LEAD / LAG CONTROL MODE

◄ ►

AUTOMATIC

The default mode will be AUTOMATIC.
Lag selections of individual systems will appear as:

OPTIONS LEAD / LAG CONTROL MODE

◄ ► MANUAL SYS 1 LEAD

OPTIONS LEAD / LAG CONTROL MODE

◄ ► MANUAL SYS 2 LEAD

OPTIONS LEAD / LAG CONTROL MODE

◄ ► MANUAL SYS 3 LEAD

SYSTEM 3 LEAD may be selected only on 3 and 4

compressor units.

OPTIONS LEAD / LAG CONTROL MODE

◄ ► MANUAL SYS 4 LEAD

SYSTEM 4 LEAD may be selected only on 4 compres-

sor units.

Содержание YCIV Series







































































































































































































































































































































Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды

York YCIV Series, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание YCIV Series

Отзывы:

Похожие инструкции для YCIV Series

Бренды по названию

Популярные бренды