Yealink Yealink SIP-T26P страница 96 Скачать руководство пользователя

Страница: 96 / 150

User Guide for the SIP-T26P IP Phone

c.) If you select No Answer Forward:

1) Press or , or the Switch soft key to select Enable from the No

Answer field.

2) Enter the destination number you want to forward unanswered incoming

calls to in the Forward To field.

3) Press or , or the Switch soft key to select the ring time to wait

before forwarding from the After Ring Time field.

The default ring time is 12 seconds.

4) (Optional.) Enter the no answer forward on code and off code respectively

in the On Code and Off Code field.

Press the Save soft key to accept the change or the Back soft key to cancel.

The icon on the idle screen indicates that call forward is enabled.

To enable call forward in custom mode:

Press Menu->Features->Call Forward.

Press or to select the desired account, and then press the Enter soft key.

Press or to select the desired forwarding type, and then press the Enter
soft key.

Depending on your selection:

a.) If you select Always Forward, you can enable it for a specific account.

1) Press or , or the Switch soft key to select Enable from the Always

field.

2) Enter the destination number you want to forward incoming calls to in the

Forward To field.

3) (Optional.) Enter the always forward on code and off code respectively in

the On Code and Off Code field.

Содержание Yealink SIP-T26P























































































































































Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды

Yealink Yealink SIP-T26P, Руководство пользователя

Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды