Yealink Yealink SIP-T26P Скачать руководство пользователя | Manualshive

Страница: 122 / 150

background image

User Guide for the SIP-T26P IP Phone

110

field.

The valid multicast IP addresses range from 224.0.0.0 to 239.255.255.255.

6.

Press the Save soft key to accept the change or the Back soft key to cancel.

Multicast paging key is configurable via web user interface at the path
DSSKey->Memory Key (or Line Key).

You can also configure the phone to use a default codec for sending multicast RTP
stream via web interface.

To configure a default codec for multicast paging via web user interface:

1.

Click on Features->General Information.

2.

Select the desired codec from the pull-down list of Multicast Codec.

The default codec is G722.

3.

Click Confirm to accept the change.

Note

To send RTP stream:

1.

Press the multicast paging key when the phone is idle.

The phone sends RTP to a preconfigured multicast address (IP: Port). Any phone in
the local network then listens to the RTP on the preconfigured multicast address (IP:
Port). For both sending and receiving of the multicast RTP, there is no SIP signaling

If G722 codec is used for multicast paging, the LCD screen displays the icon to

indicate that the phone is providing high definition voice.

Default codec for multicast paging is configurable via web user interface only.

«
...
120
121
122
123
124
...
»

Содержание Yealink SIP-T26P























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Yealink SIP-T26P

Бренд: M2M Страницы: 88

Бренд: Yealink Страницы: 3

Бренд: Yealink Страницы: 8

Бренд: Qing Xin Electronic Страницы: 45

Бренд: Denver Страницы: 168

Бренд: M4 Страницы: 13

IP Vision Dialog 4425

Бренд: Ericsson Страницы: 136

Бренд: Cooper Security Страницы: 8

Бренд: Icemobile Страницы: 20

Бренд: Grandstream Networks Страницы: 42

Бренд: Pantech Wireless Страницы: 71

Бренд: Rath Страницы: 8

Бренд: Rath Страницы: 9

Бренд: Rath Страницы: 8

Бренд: Raptor Страницы: 11

Бренд: Raptor Страницы: 12

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды