Yealink Yealink SIP-T26P страница 83 Скачать руководство пользователя

Страница: 83 / 150

Basic Call Features

To place a call using the headset:

Do one of the following:

With the optional headset connected, press to activate the headset mode.

Press the line key to obtain a dial tone.

Enter the desired number using the keypad.

Press , , or the Send soft key.

With the optional headset connected, press to activate the headset mode.

Enter the desired number using the keypad.

Press , , or the Send soft key.

Note

To place multiple calls:

You can have more than one call on your SIP-T26P IP phone. To place a new call during
an active call, do one of the following:

Press the line key. The active call is placed on hold.

Enter the desired number using the keypad.

Press , , or the Send soft key.

Press or the Hold soft key to place the original call on hold.

Press the NewCall soft key.

Enter the desired number using the keypad.

Press , , or the Send soft key.

You can press or to switch between the calls, and then press the Resume soft
key to retrieve the desired call.

When you are not in another call, you can answer a call in three ways:



Using the handset



Using the speakerphone



Using the headset

Note

To permanently activate the headset mode, refer to

Headset Prior

on page

You can ignore incoming calls by pressing the X key, the Reject soft key or the Silence soft
key. You can also activate the Do Not Disturb mode to ignore all incoming calls without
ring on your phone. For more information, refer to

Do Not Disturb (DND)

on page

You can forward incoming calls to someone else by pressing the Fwd soft key. For more
information, refer to

Call Forward

on page

Содержание Yealink SIP-T26P























































































































































Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды

Yealink Yealink SIP-T26P, Руководство пользователя

Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды