Yealink Yealink SIP-T26P Скачать руководство пользователя

Страница: 82 / 150

User Guide for the SIP-T26P IP Phone



Using the speakerphone



Using the headset

You can also dial the number first, and then choose the way you want to speak to the
other party.

You can also search and dial a contact from call history, local directory or remote phone
book. For more information, refer to

Contact Management

on page

and

Call History

Management

on page

During a call, you can alternate between Speakerphone, Headset, and Handset modes
by pressing the Speakerphone key, the HEADSET key, or picking up the handset.

The call duration of active call is visible on the LCD screen. In the figure below, the call to
Kame has lasted 1 minute and 8 seconds.

To place a call using the handset:

Pick up the handset.

Enter the desired number using the keypad.

Press , , or the Send soft key.

The # key is configured as a send key by default. You can also set the * key as the send
key, or set neither. For more information, refer to

Key as Send

on page

Note

To place a call using the hands-free speakerphone mode:

Do one of the following:

With the handset on-hook, press or the line key to obtain a dial tone.

Enter the desired number using the keypad.

Press , , or the Send soft key.

With the handset on-hook, enter the desired number using the keypad.

Press , , , or the Send soft key.

You can also dial using the SIP URI or IP address. To obtain the IP address of the phone,

press the OK key. The maximum SIP URI or IP address length is 32 characters. For
example, SIP URI: [email protected], IP: 192.168.1.15.

Your phone may not support direct IP dialing. Contact your system administrator for more
information.

Содержание Yealink SIP-T26P























































































































































Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды

Yealink Yealink SIP-T26P, Руководство пользователя

Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды