Yealink Yealink SIP-T26P Скачать руководство пользователя страница 66

Страница: 66 / 150

User Guide for the SIP-T26P IP Phone

appear on the LCD screen.

Conference

You can use this key feature to set up a conference call. For more information, refer to

Conference

on page

Dependencies:

Type (Key Event)

Key Type (Conf)

Value (the number you want to add to the conference)

Usage: Press the DSS key during an active call to set up a conference with the number
specified in the Value field.

Note

Forward

You can use this key feature to forward an incoming call to someone else. For more
information, refer to

Call Forward

on page

Dependencies:

Type (Key Event)

Key Type (Forward)

Value (the number you want to forward to)

Usage: Press the DSS key to forward an incoming call to the number specified in the
Value field.

Note

Transfer

You can use this key feature to handle the call differently depending on the transfer
mode on DSS key when there is an active call on the phone.

Dependencies:

Type (Key Event)

Key Type (Tran)

Value (the number you want to transfer to)

Usage:



When the transfer mode on DSS key is Blind Transfer, press the DSS key to complete
the blind transfer to the number specified in the Value field.



When the transfer mode on DSS key is Attended Transfer, press the DSS key to dial
out the number specified in the Value field, and then you can perform the attended
or semi-attended transfer.

When you leave the Value field blank, the DSS key performs the same function as the

Fwd soft key when receiving an incoming call.

When you leave the Value field blank, the DSS key performs the same function as the
CONF key or the Conf soft key during a call.

Содержание Yealink SIP-T26P























































































































































Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды

Yealink Yealink SIP-T26P, Руководство пользователя

Результаты поиска

Содержание Yealink SIP-T26P

Отзывы:

Похожие инструкции для Yealink SIP-T26P

Бренды по названию

Популярные бренды