manualshive.com logo in svg

YASKAWA SGD7S series, Руководство по эксплуатации продукта

Поделиться
Скачать
YASKAWA SGD7S series Скачать руководство пользователя страница 470

11.2  Hard Wire Base Block (HWBB)

11.2.7  /S-RDY (Servo Ready Output) Signal

11-6

11.2.7

 /S-RDY (Servo Ready Output) Signal

The /S-ON (Servo ON) signal will not be acknowledged in the HWBB state. Therefore, the 
Servo Ready Output Signal will turn OFF. The Servo Ready Output Signal will turn ON if both 
the /HWBB1 and /HWBB2 signals are ON and the /S-ON signal is turned OFF (BB state).

An example is provided below for when the main circuit power supply is ON and the SEN signal 
turns ON when there is no servo alarm. (An absolute encoder is used in this example.)

11.2.8

/BK (Brake Output) Signal

If the HWBB operates when the /HWBB1 or /HWBB2 signal is OFF, the /BK (Brake) signal will 
turn OFF. At that time, the setting in Pn506 (Brake Reference - Servo OFF Delay Time) will be 
disabled. Therefore, the Servomotor may be moved by external force until the actual brake 
becomes effective after the /BK signal turns OFF.

11.2.9

Stopping Methods

If the /HWBB1 or /HWBB2 signal turns OFF and the HWBB operates, the Servomotor will stop 
according to the stop mode that is set for stopping the Servomotor when the servo turns OFF 
(Pn001 = n.



X). However, if the dynamic brake is enabled (Pn001 = n.



0 or 

n.



1), observe the following precautions.

/HWBB1
/HWBB2

ON (normal 
operation)

/

S

-ON 

(

S

ervo ON 

Input 

S

ignal)

S

ERVOPACK 

S

tatu

s

/

S

-RDY 

(

S

ervo Ready 

Output 

S

ignal)

ON

OFF

ON

Operating 

S

tatu

s

HWBB 

s

tate

BB 

s

tate

ON

OFF

OFF (motor current 

s

hut-OFF reque

s

t)

ON (normal 
operation)

CAUTION

The brake signal is not a safety-related element. You must design the system so that a haz-
ardous condition does not occur even if the brake signal fails in the HWBB state. Also, if a 
Servomotor with a Brake is used, keep in mind that the brake in the Servomotor is used only 
to prevent the moving part from being moved by gravity or an external force and it cannot 
be used to stop the Servomotor.

CAUTION

The dynamic brake is not a safety-related element. You must design the system so that a 
hazardous condition does not occur even if the Servomotor coasts to a stop in the HWBB 
state. Normally, we recommend that you use a sequence that returns to the HWBB state 
after stopping for a reference.

If the application frequently uses the HWBB, stopping with the dynamic brake may result in 
the deterioration of elements in the SERVOPACK. To prevent internal elements from deterio-
rating, use a sequence in which the HWBB state is returned to after the Servomotor has 
come to a stop.

Содержание SGD7S series






















































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды