manualshive.com logo in svg

YASKAWA Motoman DX200, Инструкция по эксплуатации

Поделиться
Скачать
YASKAWA Motoman DX200 Скачать руководство пользователя страница 91

7-1

165553-1CD

HW1482183

7

Alarm  List

Conveyor Synchronized 
Funciton with Shift 
Functions

7

Alarm  List

Alarm No.

Message

Causes

Corrective Actions

1003

ROM ERROR
(YCP02)

Replace the YCP02
board (ROM).

1109

SYSTEM ERROR
(CONVEYOR)
[Decimal Data:
0 to 255]

Internal error.

Replace the YCP02 board.

1400

CONVEYOR
ENCONDER ERROR
[Error occurred 
conveyor
No.: 1, 2, 3]

Conveyor encoder error at the
error occurred conveyor No.

Replace the encoder cable 
or the encoder.

1401

CANNOT CHANGE
CONVEYOR MODE

The encoder selection “ENCODER/
VIRTUAL ENCDR” has been switched 
by the general purpose input signal 
during the conveyor synchronized 
operation.

Switch the encoder by the 
general purpose input signal 
while the manipulator is not 
in the conveyor 
synchronized
operation.

4021

MEMORY ERROR
(CONVEYOR 
CONDITION FILE)
[Decimal Data: 0 to
255]

The conveyor condition file data in
the memory has been destroyed.

Initialize the conveyor
condition file in customer
maintenance mode.

4530

CONVEYOR 
SYNCHRONIZATION
ERROR
[Decimal Data; 0 to
255]

1: The base axis specification in the
conveyor condition file is set to
other than 0, 1, and 2.
2: The robot axis specified for tracking 
does not exist.
3: The base axis specified for tracking
does not exist in the job.
The error data other than 1, 2, and
3 is an internal error.

Turn the power OFF
then back ON.
If the alarm occurs again, 
contact your YASKAWA 
representative.

4531

UNDEFINED 
CONVEYOR 
CONDITION FILE
[Decimal Data:
0 to 255]

The conveyor condition file specified
for the job is not set to “USED.”

Set the conveyor condition 
file to “USED.”

4532

CONVEYOR SPEED
DOWN
[Decimal Data:
0 to 255]

When the mode for conveyor speed
down mode in the conveyor condition
file is set to “ALARM,” the conveyor
speed is lowered to less than its lower 
limit specified in the conveyor condition 
file.

Increase the conveyor
speed so that it becomes 
higher than the conveyor 
speed lower limit specified in 
the conveyor condition
file.

4533

ARITHMETIC 
ERROR
[Decimal Data,
0 to 255]

Internal error.

Turn the power OFF
then back ON.
If the alarm occurs again, 
contact your YASKAWA 
representative.

4538

CAN NOT USE 
SMOVJ DURING 
TRACKING [10], 
Decimal Data,
0 to 255

SYMOVJ was executed when a robot
axis was used for synchronization.

SYMOVJ can be used only
when the base axis is used
for synchronization.

91 of 98

Содержание Motoman DX200



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды