manualshive.com logo in svg

YASKAWA Motoman DX200, Инструкция по эксплуатации

Поделиться
Скачать
YASKAWA Motoman DX200 Скачать руководство пользователя страница 53

3-11

165553-1CD

HW1482183

3

Teaching

3.6 Teaching After Interruption of Synchronized Motion in Playback 

Operation

Conveyor Synchronized 
Funciton with Shift 
Functions

Proceed the rest of the teaching in the same manner as the normal teaching.
To use a move instruction for synchronizing to the conveyor after having
changed to the standard interpolation mode, the operation to select the
interpolation mode for conveyor synchronized move instruction is necessary.

3.6

Teaching After Interruption of Synchronized Motion in 
Playback Operation

After the synchronized motion is interrupted by a hold operation or 
switching to teach mode during playback operation, another conveyor 
home-position cannot be registered since no conveyor home-position 
input signal is accepted.  At this moment, the tracking status in the 
conveyor tracking display is “ON” (marked with “

●

“).

In this case, another conveyor home-position can be registered by either 
of the following operations.

(1) Add a step or change the step after interruption of synchronized 

motion

(2) Perform another teaching (for other workpiece)

For the details of the above operations, refer to section 5.6 “Teaching After 
Interruption of Playback in Synchronized Operation” of “DX200 OPTIONS 
INSTRUCTION FOR CONVEYOR SYNCHRONIZED FUNCTION.”

= SYMOVL V=100.0 CV#(1) CTP=1000.000

0005

NOTE

When the start shift function is not used, as long as the 
conveyor synchronized operation is not being performed, a 
conveyor home position input signal is accepted and the 
conveyor home-position is updated. 

Therefore, even though teaching is made on the same 
conveyor position, if the conveyor home-position limit switch 
turns ON inadvertently, the conveyor position data will be 
changed. 

If there is a risk that the conveyor home-position limit switch 
is turned ON inadvertently, perform a FWD key operation 
for that step after programming a move instruction for 
conveyor synchronized motion such as SYMOVL and 
SYMOVC.

This starts the conveyor synchronized operation so that the 
conveyor home-position will not be changed even if the 
conveyor home-position limit switch turns ON. 

In this case, execute a SYEND instruction at the end of 
teaching to cancel the synchronization.

53 of 98

Содержание Motoman DX200



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды