Yamato DKN302C Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 56

background image

41

8. ERROR CODES

Reading Error Codes

DKN-C series units have a self-diagnostic function built into the CPU board and a separate safety device,
independent of the CPU board.

The table below shows possible causes and measures to take when safety device is triggered.

Error Codes

When an operational error or malfunction occurs, the alarm lamp on the control panel illuminates,
an error code is displayed, and an alarm sounds. When an error occurs, confirm the error code
and terminate operation immediately. Note that a temperature gauging error will be indicated by
ALARM lamp illuminating and accompanied by dashes in the display. No error code will be
displayed and no alarm will sound.

Safety device

Symptom

Possible causes and measures

Sensor error

detected

Alarm lamp on

in display



Temperature sensor interrupted,

disconnected or other malfunction

Contact original dealer of purchase

Short circuit

detected

Alarm lamp on

in display



Short circuit in SSR (solid state relay)

Contact original dealer of purchase

Heater

interruption

detected

Alarm lamp on

in display



Heater interrupted or disconnected



Current detection element interrupted,

disconnected or other malfunction

Contact original dealer of purchase

Memory error

Alarm lamp on

in display



Memory setting error

Contact original dealer of purchase

Internal

communication

error

Alarm lamp on

in display



Internal communication error,

temperature input circuit error

Contact original dealer of purchase

Overheat

Alarm lamp on

in display



Overheat prevention unit activated



Overheat prevention unit interrupted

disconnected or other malfunction

Check the temperature setting.
If the unit does not reset, contact service
department.

Temperature

gauging error

－－－－

in display

Gauged temperature is out of display
range
Contact original dealer of purchase

«
...
42
43
44
45
46
...
»

Содержание DKN302C

























































Отзывы:

Нет отзывов

Похожие инструкции для DKN302C

Бренд: U.S. Range Страницы: 44

Бренд: Oster Страницы: 23

Бренд: Thermador Страницы: 64

Professional VEDO127T

Бренд: Viking Страницы: 2

MFO 66 P K CD 765C

Бренд: VALBERG Страницы: 67

Бренд: Hotpoint Страницы: 20

Бренд: Maytag Страницы: 12

Бренд: Oster Страницы: 24

Бренд: DeDietrich Страницы: 13

Бренд: Euro Appliances Страницы: 24

B6ACH7A 0A Series

Бренд: NEFF Страницы: 36

Бренд: Falcon Страницы: 12

Бренд: Panasonic Страницы: 51

Бренд: Electrolux Страницы: 11

Бренд: Electrolux Страницы: 11

Бренд: Electrolux Страницы: 15

Бренд: Electrolux Страницы: 16

Бренд: Electrolux Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды