Yamato DKN302C Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 56

background image

16

4. OPERATION PROCEDURES

Operation Modes and Functions

Operation modes for this unit are defined in the table below:

N

o.

Name

Description

Page

1

Constant Temperature

Mode

Pressing the FIXED TEMP key brings up constant
temperature setup mode.
The "▲▼" keys are used to set temperature.
Pressing the RUN/STOP key initiates or terminates
operation.

20

2

Quick Auto Stop

Mode

This mode is used to automatically terminate an operation
when  a  specified  time  period  has  passed  (decided  during
operation).
This is done by pressing the TIMER key at any time during
constant temperature operation.
The "▲▼" keys are used to set the timer.
Pressing the RUN/STOP key begins operation in quick auto
stop  mode,  activates  the  timer  (once  temp  setting  is
reached)  and  automatically  terminates  operation  when
timer reaches 0:00.

21

3

Auto Stop Mode

This mode is used to automatically terminate an operation
when a specified time period has passed (decided before
operation).
Pressing the TIMER key displays "AStp".
The temperature (Sv) is set by pressing the ENTER key.
The operation time (tim) is set by pressing ENTER again.
Pressing the RUN/STOP key begins operation in auto stop
mode. Operation automatically terminates when timer
reaches 0:00.

22

4

Auto Start Mode

This operation is used to automatically begin an operation
after a specified period has passed.
Pressing the TIMER key displays "AStr".
The temperature (SV) is set by pressing the ENTER key.
The operation time (tim) is set by pressing ENTER again.
Pressing the RUN/STOP key begins operation in auto start
mode.

24

5

Programmed Operation

This operation is used to run a combination of modes, times
and temperatures as one operation.
Pressing the PROGRAM key displays "PrG1".
Press it again to select program mode.
Press the ENTER key to select the pattern (Pat). Press the
ENTER key to display "End". Enter the number of patterns
to be used.
Enter step temperatures and step times for "Sv_x" and "t_x"
respectively (where

“x” stands for a number or value).

26

*

It is not possible to change modes during operation. If a mode change is required, operation must
be terminated and a new mode of operation must be set.

«
...
17
18
19
20
21
...
»

Содержание DKN302C

























































Отзывы:

Нет отзывов

Похожие инструкции для DKN302C

Бренд: Premier Страницы: 24

Бренд: Wolf Страницы: 8

Бренд: Rangemaster Страницы: 31

Бренд: Neue Страницы: 16

Oberdome Domelok EZO-1010BL

Бренд: EaZy BrandZ Страницы: 30

Бренд: Newworld Страницы: 36

Бренд: Gaggenau Страницы: 44

Superdeck Y600 Series

Бренд: Bakers Pride Страницы: 44

Бренд: Hotpoint Страницы: 20

Бренд: ZANKER Страницы: 52

Бренд: MPM Страницы: 36

Бренд: Smeg Страницы: 36

Spacemaker TROS1500

Бренд: Black & Decker Страницы: 26

Бренд: ARDES Страницы: 25

Бренд: Jocel Страницы: 26

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 24

Бренд: BOMANN Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды