Yamato DKN302C Скачать руководство пользователя страница 17

Страница: 17 / 56

3. COMPONENT NAMES AND FUNCTIONS

Display Characters

All characters displayed when making settings and during operation are defined as follows:

Character

Identifier

Description

Purpose

Fix

Signifies constant

temperature

setting mode

Appears while entering settings for

constant temperature operation.

Signifies temperature

setting mode

Appears while entering temperature

settings.

AStP

Signifies auto stop and

quick auto stop setting

mode

Appears while entering settings for

quick auto stop or auto stop mode.

AStr

Signifies auto start

setting mode

Appears while entering settings for

auto start mode.

tim

Signifies timer setting

mode

Appears while entering timer

settings.

PrG3

Signifies which program

is being set

Appears

when

selecting

which

program to use (1, 2 or 3) See
“Programmed Operation” (P.26)

PAt

Signifies program

pattern

Appears when selecting a program
pattern.

See

“Programmed

Operation

” (P.26)

End

Signifies end of a timed

operation

Appears when a timed operation is
completed. See pgs. 19~23

Sv-1

Signifies which step

temperature is being set

Appears while setting temperature

for each step in a program. (Sv-1 to
Sv-30)

t-1

Signifies which step

timer is being set

Appears while setting timer for each

step in a program. (t-1 to t-30)

PS-3

Signifies what step is to

be repeated

Appears

when

selecting

step

numbers to be repeated in a program.
See

“Pattern Repeat Function” (P.31)

Pc-2

Signifies number of

times to repeat

Appears when setting the number of
times to repeat steps in a program.
See

“Pattern Repeat Function” (P.31)

Содержание DKN302C

























































Результаты поиска

Содержание DKN302C

Отзывы:

Похожие инструкции для DKN302C

Бренды по названию

Популярные бренды

Yamato DKN302C, Инструкция по эксплуатации

Результаты поиска

Содержание DKN302C

Отзывы:

Похожие инструкции для DKN302C

Бренды по названию

Популярные бренды