Yamato DKN302C Скачать руководство пользователя страница 31

Страница: 31 / 56

4. OPERATION PROCEDURES

Building Programs

①

Select mode and press the ENTER key.

・

When PrG1

is selected, the top display will show

・

When PrG2

is selected, the top display will show

, signifying program

“pattern”. For PrG2 pattern,

select either "1" or "2" (signifying the 2 available patterns)
using the

▲▼ keys. Press the ENTER key again. The

top display will show "End".

・

When PrG3 is selected, the top display will show "PAt1".

For PrG3

patterns, select "1", "2" or "3" (3 availble

patterns) using the

▲▼ keys. Press the ENTER key

again. Top display will show "End".

PrG1. PrG2 or PrG3 can be selected for the program example
above, since only 8 steps are used.

The following illustrates how to enter a program, using PrG3.

4. Enter program

①

Select PrG3 according to step 2, above.

②

Enter the number of steps, temperature and time for each step
(use the program planning worksheet on pages 28 & 29).

③

Press the ENTER key. Pat1 will show, flashing in top display.
("End" is shown if PrG1 is selected. In this case, go to

⑥

)

④

Select an unused pattern from among Pat1, Pat2 and Pat3
using the

▲▼ keys.

⑤

Press the ENTER key. "End" will be shown and the step
number will be shown flashing.



"End" indicates the total step numbers to be used. In the

example above, "8" would be entered here.

⑥

Enter the total number of steps (8 in the example above) to be
used, using the

▲▼ keys

⑦

Press the ENTER key.

, indicating temperature for

step 1 can now be set, will show in the top display. Current
temperature setting will also be displayed flashing in the
center display.

⑧

Set the temperature for step 1 using the

▲▼ keys.

①

②

①

②

Содержание DKN302C

























































Результаты поиска

Содержание DKN302C

Отзывы:

Похожие инструкции для DKN302C

Бренды по названию

Популярные бренды

Yamato DKN302C, Инструкция по эксплуатации

Результаты поиска

Содержание DKN302C

Отзывы:

Похожие инструкции для DKN302C

Бренды по названию

Популярные бренды