Yamaha F30D Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 84

background image

Maintenance

62

anodes.

CAUTION:

ECM00720

Do not paint anodes, as this would render

them ineffective.

NOTE:

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-

er unit.

EMU29320

Checking battery (for electric start
models)

WARNING

EWM00330

Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is
poisonous and highly caustic.
Always follow these preventive mea-

sures:

●

Avoid bodily contact with electrolytic
fluid as it can cause severe burns or
permanent eye injury.

●

Wear protective eye gear when han-
dling or working near batteries.

Antidote (EXTERNAL):

●

SKIN - Flush with water.

●

EYES - Flush with water for 15 minutes
and get immediate medical attention.

Antidote (INTERNAL):

●

Drink large quantities of water or milk
followed by milk of magnesia, beaten
egg, or vegetable oil. Get immediate
medical attention.

Batteries also generate explosive hydro-
gen gas; therefore, you should always
follow these preventive measures:

●

Charge batteries in a well-ventilated ar-
ea.

●

Keep batteries away from fire, sparks,
or open flames (for example: welding
equipment, lighted cigarettes, and so
on.)

●

DO NOT SMOKE when charging or han-
dling batteries.

KEEP BATTERIES AND ELECTROLYTIC

FLUID OUT OF REACH OF CHILDREN.

CAUTION:

ECM00360

●

A poorly maintained battery will quickly
deteriorate.

●

Ordinary tap water contains minerals
harmful to a battery, and should not be

used for topping up.

1.

Check the electrolyte level at least once
a month. Fill to the manufacturer’s rec-
ommended level when necessary. Top
up only with distilled water (or pure de-
ionized water suitable to use in batter-

ZMU02820

ZMU04092

✩✪✰✬✤ ✩✥

«
...
65
66
67
68
69
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Бренд: Balluff Страницы: 62

Бренд: Garelick Страницы: 3

Бренд: MSI Страницы: 112

ADRF5515A-EVALZ

Бренд: Analog Devices Страницы: 9

B450M MORTAR TITANIUM

Бренд: MSI Страницы: 144

Бренд: C&T Solution Страницы: 84

Бренд: MSI Страницы: 91

SERVER SYSTEM SR2500AL

Бренд: Intel Страницы: 210

Бренд: AOpen Страницы: 8

tKINO-AL-E1-R10

Бренд: IEI Technology Страницы: 12

Бренд: Atmel Страницы: 39

Бренд: Gigabyte Страницы: 37

Бренд: Acrosser Technology Страницы: 3

Бренд: unicore Страницы: 29

Бренд: unicore Страницы: 28

Бренд: ASROCK Страницы: 83

Бренд: DFI Страницы: 26

Бренд: DFI Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды