Yamaha F30D Скачать руководство пользователя страница 25

Страница: 25 / 84

Basic components

protect the engine from electrochemical
corrosion. Never paint the trim tab as it

will become ineffective as an anode.

EMU26312

Tilt lock mechanism

The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the wa-
ter when in reverse gear.

To lock it, set the tilt lock lever in the “

”

(lock) position. To release, push the tilt lock
lever in the “

” (release) position.

EMU26320

Tilt support knob

To keep the outboard motor in the tilted up
position, push the tilt support knob under the
swivel bracket.

EMU26372

Top cowling lock lever(s) (turn type)

To remove the engine top cowling, turn the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling again by returning the lever(s) to the
lock position.

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 49.

1. Trim tab
2. Bolt

1. Tilt lock lever

ZMU02822

ZMU04039

1. Top cowling lock lever(s)

ZMU04040

ZMU04041

✩✪✰✬✤ ✥✣

Содержание F30D





















































































Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды

Yamaha F30D, Руководство пользователя

Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды