Yamaha F30D Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 84

background image

Important manual information

EMU25100

To the owner

Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding
of these simple instructions will help you ob-
tain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.

The Safety Alert Symbol means

ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!

WARNING

EWM00780

Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the out-

board motor.

CAUTION:

ECM00700

A CAUTION indicates special precautions
that must be taken to avoid damage to the

outboard motor.

NOTE:

A NOTE provides key information to make

procedures easier or clearer.

Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current prod-
uct information available at the time of print-
ing, there may be minor discrepancies
between your machine and this manual. If
there is any question concerning this manu-

al, please consult your Yamaha dealer.

NOTE:

The F30TR, F40MH, F40TR and the stan-
dard accessories are used as a base for the
explanations and illustrations in this manual.
Therefore some items may not apply to ev-

ery model.

EMU25110

F30D, F40D

OWNER’S MANUAL

©2004 by Yamaha Motor Corporation, USA

1st edition, April 2004

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in Japan

P/N LIT-18626-06-02

✩✪✰✬✤ ✤

«
1
2
3
4
5
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Бренд: IBASE Technology Страницы: 33

Бренд: Lantronix Страницы: 8

Бренд: AOpen Страницы: 8

RHINO VAP133-ACP

Бренд: Octek Страницы: 66

Бренд: Beagleboard.org Страницы: 2

Бренд: VIA Technologies Страницы: 76

Бренд: JETWAY Страницы: 37

Бренд: Aaeon Страницы: 119

Бренд: Aaeon Страницы: 113

Бренд: IDT Страницы: 18

Бренд: Texas Instruments Страницы: 13

Бренд: Gigabyte Страницы: 86

Бренд: MSI Страницы: 98

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 129

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 108

Memorator Pro 2xHS v2 CB

Бренд: Kvaser Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды