Yamaha F30D Скачать руководство пользователя страница 27

Страница: 27 / 84

Basic components

indicator will flash. For further information on
reading the indicator, see page 22.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26610

Trim meter

This gauge shows the trim angle of your out-
board motor.

NOTE:

Memorize the trim angles that work best for
your boat under different conditions. Adjust
the trim angle to the desired setting with the

power trim and tilt switch.

EMU26801

Warning system

CAUTION:

ECM00090

Do not continue to operate the engine if a
warning device has activated. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

EMU26813

Overheat warning

This engine has an overheat warning device.
If the engine temperature rises too high, the
warning device will activate.

Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The overheat warning indicator will light (if
equipped on the bottom cowling or the ta-
chometer).

●

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main

ZMU04715

ZMU04581

ZMU04746

ZMU04044

✩✪✰✬✤ ✥✥

Содержание F30D





















































































Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды

Yamaha F30D, Руководство пользователя

Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды