Yamaha F30D Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 84

background image

Operation

39

salt corrosion.

WARNING

EWM00220

Be sure all people are clear of the out-
board motor when tilting up and down,
also be careful not to pinch any body
parts between the drive unit and engine

bracket.

WARNING

EWM00250

Leaking fuel is a fire hazard. If there is a
fuel joint on the outboard motor, discon-
nect the fuel line or close the fuel cock if
the engine will be tilted for more than a

few minutes. Otherwise fuel may leak.

CAUTION:

ECM00241

●

Before tilting the outboard motor, stop
the engine by following the procedure
on page 35. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this

could break the handle.

EMU27995

Procedure for tilting up (hydro tilt
models)

1.

Place the remote control lever / gear
shift lever in neutral.

2.

Disconnect the fuel line from the out-
board motor.

3.

Place the tilt lock lever in the release po-
sition.

4.

Hold the rear of the top cowling with one
hand, tilt the engine up, and turn the tilt
support lever toward you or tilt support
knob into the clamp bracket, and then
place the tilt lock lever back into the lock
position to support the outboard motor.

N

ZMU03087

N

F

R

ZMU04062

ZMU04063

ZMU04064

✩✪✰✬✤ ✦✬

«
...
42
43
44
45
46
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

ADSP-BF518F EZ-Board

Бренд: Analog Devices Страницы: 111

Бренд: Biostar Страницы: 47

Бренд: Biostar Страницы: 45

Бренд: AOpen Страницы: 8

Бренд: Aaeon Страницы: 97

Бренд: Supermicro Страницы: 256

Бренд: Quick Страницы: 48

Бренд: Pentair Страницы: 4

Бренд: JETWAY Страницы: 47

Бренд: Richtek Страницы: 15

Бренд: Biostar Страницы: 40

Бренд: Supero Страницы: 97

Бренд: IDT Страницы: 43

Бренд: TRIGEM Страницы: 17

GA-HA65M-D2H-B3

Бренд: Gigabyte Страницы: 104

Бренд: ON Semiconductor Страницы: 2

Бренд: MSI Страницы: 169

Бренд: CDI Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды