Yamaha F30D Скачать руководство пользователя страница 34

Страница: 34 / 84

Operation

connect the fuel line to the joint. Then
firmly connect the other end of the fuel
line to the joint on the fuel tank.

If a steering friction adjuster is provided
on your outboard motor, securely attach
the fuel line to the fuel line clamp.

NOTE:

During engine operation place the tank hori-
zontally, otherwise fuel cannot be drawn

from the fuel tank.

Squeeze the primer pump with the outlet
end up until you feel it become firm.

EMU27490

Starting engine

EMU27541

Starting engine

Place the gear shift lever in neutral.

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-

tral.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the

ZMU04048

ZMU02024

ZMU02025

ZMU04049

✩✪✰✬✤ ✥✬

Содержание F30D





















































































Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды

Yamaha F30D, Руководство пользователя

Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды