Yamaha F30D Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 84

background image

Operation

32

EMU27670

Warming up engine

EMU27710

Manual start and electric start
models

1.

After starting the engine, allow it to idle
for 3 minutes to warm up. Failure to do
so will shorten engine life.

2.

Be sure the low oil pressure warning in-
dicator goes off after starting the engine.

3.

Check for a steady flow of water from the
cooling water pilot hole.

CAUTION:

ECM00210

●

If the low oil pressure warning indicator
does not go off after the engine starts,
stop the engine. Otherwise serious en-
gine damage could occur. Check the oil
level and add oil if necessary. Consult
your Yamaha dealer if the cause for the
low oil pressure warning indicator can-
not be found.

●

A continuous flow of water from the pi-
lot hole shows that the water pump is
pumping water through the cooling
passages. If water is not flowing out of
the pilot hole at all times while the en-
gine is running, overheating and seri-
ous damage could occur. Stop the
engine and check whether the cooling
water inlet on the lower case or the
cooling water pilot hole is blocked.
Consult your Yamaha dealer if the prob-

lem cannot be located and corrected.

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the

engine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and

ZMU04051

ZMU04052

✩✪✰✬✤ ✦✥

«
...
35
36
37
38
39
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Бренд: Quectel Страницы: 34

Бренд: AOpen Страницы: 8

Бренд: Navia Страницы: 26

Бренд: MSI Страницы: 48

Бренд: Avalue Technology Страницы: 82

Бренд: MSI Страницы: 71

Бренд: ASROCK Страницы: 56

Бренд: Biostar Страницы: 23

Бренд: Gigabyte Страницы: 96

MPG Z390 GAMING EDGE AC

Бренд: MSI Страницы: 87

Бренд: Unicorn Computer Страницы: 36

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

Бренд: Caji Страницы: 19

ISOFACE ISO2H823V2

Бренд: Infineon Страницы: 28

Бренд: TYAN Страницы: 164

Бренд: ST Страницы: 52

Бренд: MSI Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды