Yamaha F30D Скачать руководство пользователя страница 64

Страница: 64 / 84

Maintenance

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines / shear pin for wear or
damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-

age.

NOTE:

If the shear pin equipped: it is designed to
break if the propeller hits a hard underwater
obstacle to help protect the propeller and
drive mechanism. The propeller will then
spin freely on the shaft. If this happens, the

shear pin must be replaced.

EMU29193

Removing the propeller

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

Remove the propeller and thrust wash-
er.

EMU29230

Installing the propeller

CAUTION:

ECM00340

●

Be sure to install the thrust washer be-
fore installing the propeller, otherwise
the lower case and propeller boss

ZMU04089

ZMU01897

1. Cotter pin
2. Propeller nut
3. Washer
4. Spacer
5. Propeller
6. Thrust washer

✩✪✰✬✤ ✬

Содержание F30D





















































































Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды

Yamaha F30D, Руководство пользователя

Результаты поиска

Содержание F30D

Отзывы:

Похожие инструкции для F30D

Бренды по названию

Популярные бренды