Yamaha F30D Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 84

background image

Maintenance

47

with a minimum of tools, can perform the fol-
lowing procedures.

CAUTION:

ECM01080

●

To prevent problems which can be
caused by oil entering the cylinder from
the sump, keep the outboard motor in
the attitude shown when transporting
and storing it. If storing or transporting
the outboard motor on its side (not up-
right), put it on a cushion after draining
the engine oil.

●

Do not place the outboard motor on its
side before the cooling water has
drained from it completely, otherwise
water may enter the cylinder through
the exhaust port and cause engine trou-
ble.

●

Store the outboard motor in a dry, well-

ventilated place, not in direct sunlight.

EMU28301

Procedure

EMU28372

Flushing in a test tank

1.

Wash the outboard motor body using
fresh water. For further information, see
page 50.

2.

Fill the fuel tank with fresh fuel and add
one ounce of “Yamaha Fuel Conditioner
and Stabilizer” (Part No. LUB-FUELC-
12-00) to each gallon of fuel.

NOTE:

The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is

to be drained instead.

3.

Remove the engine top cowling and si-
lencer cover.

4.

Install the outboard motor on the test
tank.

5.

Fill the tank with fresh water to above the
level of the anti-cavitation plate.

CAUTION:

ECM00300

Do not run the engine without supplying
it with cooling water. Either the engine
water pump will be damaged or the en-

ZMU04078

ZMU04079

1. Water surface
2. Lowest water level

ZMU02051

1

2

✩✪✰✬✤ ✧✪

«
...
50
51
52
53
54
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Бренд: NXP Semiconductors Страницы: 12

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 19

Бренд: Aeroflex Страницы: 20

Бренд: Avalue Technology Страницы: 89

Бренд: MAX power Страницы: 20

MT9J003I12STCVH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Gigabyte Страницы: 81

Бренд: JETWAY Страницы: 57

Бренд: Advantech Страницы: 82

Бренд: Microsemi Страницы: 22

GA-Z97X-Gaming G1

Бренд: Gigabyte Страницы: 136

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: ASROCK Страницы: 237

Бренд: THORLABS Страницы: 22

Бренд: ASROCK Страницы: 160

Бренд: u-blox Страницы: 37

Бренд: TYAN Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды