Yamaha F30D Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 84

background image

Trouble Recovery

71

5.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope several turns
around the flywheel clockwise.

6.

Pull the rope slowly until resistance is
felt.

7.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

NOTE:

When the engine does not start with this pro-

cedure, see page 29.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-

dure below in order to minimize engine dam-
age.

EMU29783

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

2.

Remove the spark plug(s), then face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

3.

Drain the fuel from the carburetor, fuel
filter, and fuel line. Drain the engine oil
completely.

4.

Fill the sump with the fresh engine oil.

5.

Feed engine fogging oil or engine oil
through the carburetor(s) and spark plug
holes while cranking the engine with the
manual starter or emergency starter
rope.

6.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor

until it has been completely inspected.

ZMU03387

ZMU04100

Engine oil capacity:

2.0 L (2.11 US qt) (1.76 Imp.qt)

✩✪✰✬✤ ✪✤

«
...
74
75
76
77
78
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Cyclone IV GX FPGA

Бренд: Altera Страницы: 60

Бренд: Alcad Страницы: 98

Бренд: Aeroflex Страницы: 20

Бренд: ST Страницы: 9

Бренд: MSI Страницы: 76

Бренд: DFI Страницы: 99

Бренд: Texas Instruments Страницы: 101

Бренд: JETWAY Страницы: 56

Бренд: Analog Devices Страницы: 13

Z690 Phantom Gaming 4

Бренд: ASROCK Страницы: 109

Бренд: Biostar Страницы: 85

TPS61090EVM-029

Бренд: Texas Instruments Страницы: 19

GeForce 8300 (MI-A78U-8309)

Бренд: XFX Страницы: 26

Бренд: IBASE Technology Страницы: 64

B85M-P32 series

Бренд: MSI Страницы: 186

Бренд: IBASE Technology Страницы: 72

Бренд: Acrosser Technology Страницы: 3

Бренд: Ublox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды