Yamaha F30D Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 84

background image

Operation

41

sure.

5.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28041

Procedure for tilting down (manual
and hydro tilt models)

1.

Release the tilt lock lever.

2.

Hold the rear of the top cowling with one
hand, tilt the outboard motor up slightly
and pull out the tilt support knob or re-
turn the tilt support lever.

3.

Slowly tilt the outboard motor down.

4.

Place the tilt lock lever in the lock posi-
tion.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

ZMU04069

ZMU04070

ZMU04071

✩✪✰✬✤ ✧✤

«
...
44
45
46
47
48
...
»

Содержание F30D





















































































Отзывы:

Нет отзывов

Похожие инструкции для F30D

Бренд: Yamaha Страницы: 497

Бренд: MPS Страницы: 6

ATmega328P Xplained Mini

Бренд: Microchip Technology Страницы: 26

Бренд: Sun Microsystems Страницы: 74

TA870 PLUS - SETUP 2

Бренд: Biostar Страницы: 67

Бренд: Zotac Страницы: 56

Бренд: Quantum Design Страницы: 77

Бренд: Aaeon Страницы: 95

Бренд: Gigabyte Страницы: 112

Бренд: BESTEK Страницы: 47

Бренд: ASROCK Rack Страницы: 93

Бренд: JETWAY Страницы: 44

Бренд: JETWAY Страницы: 57

Бренд: ITOX Страницы: 114

Бренд: Merit Страницы: 4

Бренд: Maxus Страницы: 59

MT9V113PACSTCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Analog Devices Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды