Yamaha F150C страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 80

background image

Maintenance

59

●

Connect the red battery cable first when
installing the battery and disconnect the
black battery cable first when removing
it. Otherwise, the electrical parts can be
damaged.

●

The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start
the engine.

Connect the RED battery cable to the POSI-
TIVE (+) terminal first. Then connect the
BLACK battery cable to the NEGATIVE (-) ter-
minal.

Connecting an accessory battery (optional)
1.

Remove the accessory battery coupler
cover from the outboard motor.

2.

Connect the accessory battery coupler to
the coupler of the accessory battery ca-
ble (optional). Use a connecting cable be-
tween the (-) terminals of the starting
battery and accessory battery. See the il-
lustrations of the wiring connections. This
cable must be made from wire thicker
than the starting battery cable.

WARNING

EWM00600

Use of smaller wire could lead to a fire.

NOTE:

If connecting an accessory battery, consult
your Yamaha dealer about correct wiring.

EMU29370

Disconnecting the battery

Disconnect the BLACK cable from the NEGA-
TIVE (-) terminal first. Then disconnect the
RED cable from the POSITIVE (+) terminal.

EMU29390

Checking top cowling

Check the fitting of the top cowling by pushing
it with both hands. If it is loose have it repaired
by your Yamaha dealer.

1. Red cable

2. Black cable
3. Battery

1. Battery for starting

2. Battery for accessories

3. Large red lead for starting battery

4. Small red lead for accessory battery

charging (optional part)

5. Large black lead

6. Negative connecting cable

7. Power for accessories

63P10.book Page 59 Tuesday, May 13, 2003 10:23 AM

«
...
63
64
65
66
67
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

Бренд: ECS Страницы: 27

Бренд: Advantech Страницы: 118

Spacewalker AK32

Бренд: Shuttle Страницы: 89

Бренд: Freescale Semiconductor Страницы: 4

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Advance 10T Series

Бренд: QDI Страницы: 74

DiskOnChip PCI-G-EVB

Бренд: M-system Страницы: 14

Бренд: FIC Страницы: 52

Бренд: Gigabyte Страницы: 18

Бренд: Pentair Страницы: 4

Бренд: JETWAY Страницы: 41

Бренд: Biostar Страницы: 40

Бренд: Gigabyte Страницы: 104

Бренд: Cebekit Страницы: 8

Бренд: Pericom Страницы: 8

Бренд: MSI Страницы: 6

Бренд: Yamaha Страницы: 82

Бренд: Gigabyte Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды