Yamaha F150C страница 35 Скачать руководство пользователя | Manualshive

Страница: 35 / 80

background image

Operation

29

EMU27100

Preoperation checks

WARNING

EWM00080

If any item in the preoperation check is not
working properly, have it inspected and
repaired before operating the outboard
motor. Otherwise an accident could occur.

CAUTION:

ECM00120

Do not start the engine out of water. Over-
heating and serious engine damage can
occur.

EMU27110

Fuel

●

Check to be sure you have plenty of fuel for
your trip.

●

Make sure there are no fuel leaks or gaso-
line fumes.

●

Check fuel line connections to be sure they
are tight (if equipped Yamaha fuel tank or
boat tank).

●

Be sure the fuel tank is positioned on a se-
cure, flat surface, and that the fuel line is not
twisted or flattened, or likely to contact
sharp objects (if equipped Yamaha fuel
tank or boat tank).

EMU27130

Controls

●

Check throttle, shift, and steering for proper
operation before starting the engine.

●

The controls should work smoothly, without
binding or unusual free play.

●

Look for loose or damaged connections.

●

Check operation of the starter and stop
switches when the outboard motor is in the
water.

EMU27150

Engine

●

Check the engine and engine mounting.

●

Look for loose or damaged fasteners.

●

Check the propeller for damage.

●

Check that the battery is in good condition
and the battery connections are secure.

EMU27161

Checking the engine oil level

1.

Put the outboard motor in an upright po-
sition (not tilted).

2.

Remove oil dipstick and wipe it clean.

3.

Completely insert the dipstick and re-
move it again.

4.

Check the oil level using the dipstick to be
sure the level falls between the upper and
lower marks. Fill with oil if it is below the
lower mark, or drain to the specified level
if it is above the upper mark.

NOTE:

Be sure to completely insert the dipstick into
the dipstick guide.

EMU30020

Filling fuel

WARNING

EWM00060

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other sourc-
es of ignition.

1.

Remove the fuel tank cap.

2.

Carefully fill the fuel tank.

1. Oil dipstick
2. Lower level mark

3. Upper level mark

63P10.book Page 29 Tuesday, May 13, 2003 10:23 AM

«
...
33
34
35
36
37
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

JW-A880GM-FUSION

Бренд: J&W Страницы: 38

B85 Anniversary

Бренд: ASROCK Страницы: 148

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

Бренд: AMPTRON Страницы: 41

Бренд: C&T Solution Страницы: 65

Бренд: Intel Страницы: 12

Бренд: DFI Страницы: 120

Бренд: Gigabyte Страницы: 18

Бренд: Avalue Technology Страницы: 116

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

Бренд: Biostar Страницы: 115

Бренд: TYAN Страницы: 164

Бренд: TDK Страницы: 11

Бренд: JETWAY Страницы: 54

Бренд: Intel Страницы: 87

XtremeDSP Spartan-3A DSP 3400A...

Бренд: Xilinx Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды