Yamaha F150C Скачать руководство пользователя

Страница: 28 / 80

Basic components

NOTE:

The fuel level reading can be affected by the
position of the sensor in the fuel tank and the
attitude of the boat in the water. Operation
with bow-up trim or continuous turning can
give false readings.

EMU26720

Fuel warning indicator

If the fuel level decreases to one segment, the
fuel level warning segment will begin to blink.

CAUTION:

ECM00880

Do not continue to operate the engine with
full throttle if a warning device has activat-
ed. Get back to the port within trolling en-
gine speed.

EMU26730

Low battery voltage warning indicator

If battery voltage drops, the display will auto-
matically turn on and begin to blink.

CAUTION:

ECM00870

Get back to the port soon if a warning de-
vice has activated. For charging the bat-
tery, consult your Yamaha dealer.

EMU26740

Fuel management meter

The fuel management meter shows the state
of the fuel consumption while the engine is
running.

NOTE:

After the main switch is first turned on, all seg-
ments of the display come on as a test. After
a few seconds, the gauge will change to nor-

1. Fuel level warning segment

ZMU01745

1. Low battery indicator

1. Fuel flow meter

2. Fuel consumption meter / Fuel economy

meter / Twin engine speed synchronizer

3. Water separator warning indicator (operates

only if the sensor has been installed)

ZMU01748

63P10.book Page 22 Tuesday, May 13, 2003 10:23 AM

Содержание F150C

















































































Результаты поиска

Содержание F150C

Отзывы:

Похожие инструкции для F150C

Бренды по названию

Популярные бренды

Yamaha F150C, Руководство пользователя

Результаты поиска

Содержание F150C

Отзывы:

Похожие инструкции для F150C

Бренды по названию

Популярные бренды