Yamaha F150C Скачать руководство пользователя | Manualshive

Страница: 67 / 80

background image

Trouble Recovery

61

EMU29421

Troubleshooting

A problem in the fuel, compression, or ignition
systems can cause poor starting, loss of pow-
er, or other problems. This section describes
basic checks and possible remedies, and cov-
ers all Yamaha outboard motors. Therefore
some items may not apply to your model.
If your outboard motor requires repair, bring it
to your Yamaha dealer.
If the engine trouble warning indicator is flash-
ing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of rec-
ommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?
A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 30.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten all
loose connections. Replace worn or broken
wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine stop switch lanyard not at-
tached?
A. Attach lanyard.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. A spark plug(s) fouled or of incorrect type?
A. Inspect spark plug(s). Clean or replace with
recommended type.

Q. Is fuel system obstructed?

63P10.book Page 61 Tuesday, May 13, 2003 10:23 AM

«
...
65
66
67
68
69
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 24

Бренд: ASROCK Страницы: 154

Z690M DS3H DDR4

Бренд: Gigabyte Страницы: 36

Бренд: Erreka Страницы: 4

Бренд: DFI Страницы: 48

Бренд: VIA Technologies Страницы: 15

Бренд: Acorp Страницы: 54

Side-Power SX100/185T

Бренд: SLEIPNER MOTOR AS Страницы: 16

MPG B550I GAMING EDGE WIFI

Бренд: MSI Страницы: 69

TAS5001-5122C2EVM

Бренд: Texas Instruments Страницы: 27

Бренд: IBASE Technology Страницы: 78

Бренд: Texas Instruments Страницы: 33

Бренд: DFI Страницы: 105

Бренд: DFI Страницы: 114

Бренд: DFI Страницы: 183

Бренд: Global Страницы: 37

Motherboard PR-DLS533

Бренд: Asus Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды