manualshive.com logo in svg

Yamaha F150C, Руководство пользователя

Поделиться
Скачать
Yamaha F150C Скачать руководство пользователя страница 71

Trouble Recovery

65

EMU29470

Replacing fuse

If a fuse has blown, remove the electrical cov-
er, open the fuse holder and remove the fuse
with a fuse puller (if equipped). Replace it with
a spare one of the proper amperage.

WARNING

EWM00630

Be sure to use the specified fuse. An in-
correct fuse or a piece of wire could allow
excessive current flow. This could cause
electric system damage and a fire hazard.

NOTE:

Consult your Yamaha dealer if the new fuse
immediately blows again.

EMU29520

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt/ the power tilt because
of a discharged battery or a failure with the
power trim and tilt unit/the power tilt, the en-
gine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

1. Electrical cover
2. Fuse puller

3. Accessory fuse (50 A)

4. Main fuse (50 A)
5. Main switch / trim switch fuse (20 A)

6. Engine control unit / ignition coil / electric 

fuel pump / fuel injector / ISC (idle speed 
control) fuse (20 A)

7. Starter relay fuse (30 A)
8. Spare fuse (20 A, 30 A, 50 A)

63P10.book  Page 65  Tuesday, May 13, 2003  10:23 AM

Содержание F150C

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды