Yamaha F150C Скачать руководство пользователя | Manualshive

Страница: 33 / 80

background image

Operation

27

EMU26900

Installation

CAUTION:

ECM00110

Incorrect engine height or obstructions to
smooth water flow (such as the design or
condition of the boat, or accessories such
as transom ladders or depth finder trans-
ducers) can create airborne water spray
while the boat is cruising. Severe engine
damage may result if the motor is operat-
ed continuously in the presence of air-
borne water spray.

NOTE:

During water testing check the buoyancy of
the boat, at rest, with its maximum load.
Check that the static water level on the ex-
haust housing is low enough to prevent water
entry into the powerhead, when water rises
due to waves when the outboard is not run-
ning.

EMU26910

Mounting the outboard motor

WARNING

EWM00820

●

Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower than
the maximum rating on the capacity
plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.

●

The information presented in this sec-
tion is intended as reference only. It is
not possible to provide complete in-
structions for every possible boat and
motor combination. Proper mounting
depends in part on experience and the
specific boat and motor combination.

WARNING

EWM00830

Improper mounting of the outboard motor
could result in hazardous conditions such
as poor handling, loss of control, or fire
hazards. Observe the following:

●

For permanently mounted models, your
dealer or other person experienced in
proper rigging should mount the motor.
If you are mounting the motor yourself,
you should be trained by an experienced
person.

●

For portable models, your dealer or oth-
er person experienced in proper out-
board motor mounting should show you
how to mount your motor.

Mount the outboard motor on the center line
(keel line) of the boat, and ensure that the
boat itself is well balanced. Otherwise the
boat will be hard to steer. For boats without a
keel or which are asymmetrical, consult your
dealer.

1. Center line (keel line)

ZMU01760

1

63P10.book Page 27 Tuesday, May 13, 2003 10:23 AM

«
...
31
32
33
34
35
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

Бренд: Abit Страницы: 112

A75A-G35 Series

Бренд: MSI Страницы: 72

Бренд: Advantech Страницы: 3

Intel P43 Series

Бренд: J&W Страницы: 37

Бренд: Xilinx Страницы: 70

Бренд: Alpha Data Страницы: 40

Бренд: Texas Instruments Страницы: 19

Бренд: Acorp Страницы: 66

Бренд: IEI Technology Страницы: 21

Бренд: Humandata Страницы: 10

Бренд: ASROCK Страницы: 257

LCMXO3L-DSI-EVN

Бренд: Lattice Страницы: 2

PROTO1 Xplained Pro

Бренд: Atmel Страницы: 17

Бренд: Advantech Страницы: 98

Бренд: JETWAY Страницы: 48

Бренд: Gigabyte Страницы: 44

Бренд: Texas Instruments Страницы: 31

STEVAL-IHM011V1

Бренд: ST Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды