manualshive.com logo in svg

Yamaha F150C, Руководство пользователя

Поделиться
Скачать
Yamaha F150C Скачать руководство пользователя страница 15

General information

9

●

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after refu-
eling.

●

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.

●

If any gasoline spills onto your skin, im-
mediately wash with soap and water.
Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electrostat-
ic sparks.

CAUTION:

ECM00010

Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign matter.

EMU25570

Gasoline

If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets minimum octane ratings. Yamaha
does not recommended gasohol containing
methanol because it can cause fuel system
damage or engine performance problems.

EMU25680

Engine oil

CAUTION:

ECM01050

All 4-stroke engines are shipped from the
factory without engine oil.

EMU25700

Battery requirement

CAUTION:

ECM01060

Do not use a battery that does not meet the
specified capacity. If a battery which does
not meet specifications is used, the elec-

Recommended gasoline:

Regular unleaded gasoline with a 
minimum octane rating of 86 (Pump 
Octane Number) = (R+M)/2

Recommended engine oil:

4-stroke motor oil with a combination of 
corresponding SAE and API as shown 
in the chart

Engine oil quantity (excluding oil filter):

5.2 L (5.50 US qt) (4.58 Imp.qt)

ZMU01710

63P10.book  Page 9  Tuesday, May 13, 2003  10:23 AM

Содержание F150C

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды