Yamaha F150C Скачать руководство пользователя | Manualshive

Страница: 50 / 80

background image

Maintenance

44

2.

Screw the garden hose connector onto a
garden hose which is connected to a
fresh water supply.

3.

With the engine off, turn on the water tap
and let the water flush through the cool-
ing passages for about 15 minutes. Turn
off the water and disconnect the garden
hose.

4.

When flushing is complete, reinstall the
garden hose connector on the fitting on
the bottom cowling. Tighten the connec-
tor securely.

CAUTION:

ECM00540

Do not leave the garden hose connector
loose on the bottom cowling fitting or let
the hose hang free during normal opera-
tion. Water will leak out of the connector
instead of cooling the engine, which can

cause serious overheating. Be sure the
connector is tightened securely on the fit-
ting after flushing the engine.

NOTE:

●

When flushing the engine with the boat in
the water, tilting up the outboard motor until
it is completely out of the water will achieve
better results.

●

For cooling system flushing instructions,
see page 41.

EMU28450

Cleaning the outboard motor

After use, wash the exterior of the outboard
motor with fresh water. Flush the cooling sys-
tem with fresh water.

NOTE:

For cooling system flushing instructions, see
page 41.

EMU28460

Checking painted surface of motor

Check the motor for scratches, nicks, or flak-
ing paint. Areas with damaged paint are more
likely to corrode. If necessary, clean and paint
the areas. A touch-up paint is available from
your Yamaha dealer.

1. Fitting
2. Garden hose connector

3. Garden hose

63P10.book Page 44 Tuesday, May 13, 2003 10:23 AM

«
...
48
49
50
51
52
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

Бренд: Panasonic Страницы: 26

Бренд: ICP Страницы: 50

Бренд: MSI Страницы: 104

Бренд: JETWAY Страницы: 19

Бренд: IWILL Страницы: 54

Бренд: Micrel Страницы: 10

Бренд: ASROCK Страницы: 244

Бренд: Acorp Страницы: 54

Бренд: ASRock Industrial Страницы: 41

Бренд: Wemos Страницы: 12

Бренд: Wolfson Страницы: 12

EVB-LAN9252-SPI

Бренд: Microchip Technology Страницы: 22

Бренд: Freescale Semiconductor Страницы: 17

Бренд: Gigabyte Страницы: 92

73-30130-00877-9

Бренд: Kvaser Страницы: 16

Бренд: AMD Страницы: 36

Бренд: MSI Страницы: 169

Бренд: EPOX Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды