Yamaha F150C страница 56 Скачать руководство пользователя | Manualshive

Страница: 56 / 80

background image

Maintenance

50

Checkpoints

●

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage

●

Fuel connector leakage

EMU28980

Inspecting fuel filter

WARNING

EWM00310

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

EMU29960

Cleaning fuel filter

1.

Loosen the filter cup ring nut.

2.

Remove the filter cup, catching any
spilled fuel in a rag.

3.

Remove the filter element, and wash it in
solvent. Allow it to dry. Inspect the filter el-
ement and O-ring to make sure they are
in good condition. Replace them if neces-
sary. If any water is found in the fuel, the
Yamaha portable fuel tank or other fuel
tanks should be checked and cleaned.

1. Locking tab

2. Filter cup ring nut

63P10.book Page 50 Tuesday, May 13, 2003 10:23 AM

«
...
54
55
56
57
58
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

RouterBOARD 411

Бренд: 4gon Страницы: 2

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: Gigabyte Страницы: 104

Бренд: ASROCK Страницы: 43

Бренд: Supermicro Страницы: 229

Бренд: Pure Photonics Страницы: 11

Бренд: Octek Страницы: 84

Бренд: DFI Страницы: 78

Бренд: DFI Страницы: 132

Бренд: DFI-ITOX Страницы: 124

Бренд: I-Bus Страницы: 140

Бренд: CHAINTECH Страницы: 48

Бренд: CHAINTECH Страницы: 33

Бренд: ASROCK Страницы: 7

Бренд: ASROCK Страницы: 7

Бренд: ASROCK Страницы: 144

Бренд: ASROCK Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды