Yamaha F150C Скачать руководство пользователя | Manualshive

Страница: 43 / 80

background image

Operation

37

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever toward
you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure to
support it with the tilt support knob or tilt
support lever. Otherwise the outboard mo-
tor could fall back down suddenly if oil in
the power trim and tilt unit loses pressure.

5.

If the trim rods equipped: once the out-
board motor is supported with the tilt sup-
port lever, press the power trim and tilt
switch “

” (down) to retract the trim

rods.

CAUTION:

ECM00250

Be sure to retract the trim rods completely
during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt
mechanism.

EMU28050

Procedure for tilting down (power trim
and tilt/power tilt models)

Power trim and tilt model / power tilt model
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt sup-
port lever / tilt support knob becomes
free.

2.

Release the tilt support lever or pull out
the tilt support knob.

3.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

63P10.book Page 37 Tuesday, May 13, 2003 10:23 AM

«
...
41
42
43
44
45
...
»

Содержание F150C

















































































Отзывы:

Нет отзывов

Похожие инструкции для F150C

Бренд: DFI Страницы: 104

GeForce 8300 (MI-A78U-8309)

Бренд: XFX Страницы: 26

Бренд: BCM Страницы: 5

Бренд: Gigabyte Страницы: 88

Бренд: ST Страницы: 47

Бренд: Infineon Страницы: 30

Бренд: DFI Страницы: 71

Бренд: Caen RFID Страницы: 29

SMART SPMXCA200

Бренд: Spektrum Страницы: 16

Stratix II GX PCI Express

Бренд: Altera Страницы: 70

Бренд: Redpine Signals Страницы: 70

Бренд: Lantronix Страницы: 93

K7VM400M Pro Series

Бренд: QDI Страницы: 62

Бренд: Habey Страницы: 4

Бренд: Abit Страницы: 110

Бренд: Eurotech Страницы: 32

Бренд: Eurotech Страницы: 56

Бренд: Gigabyte Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды