Yaesu WIRES-X TM-400XDE, Инструкция по эксплуатации

Страница: 32 / 66

31

FTM-400XD/D
1. Press the [
D X
] key on the portable node FTM-400XD/D transceiver.
The “ X ” icon flashes on the upper left of the LCD screen.
• The display screen example shows the “
Access Point
” screen. In “
Direct Operation
”,
“ DIRECT ” is displayed instead of the frequency
• If the “ X ” icon does not blink when the [ D X ] key is pressed, communication between the
transceiver connected to the PC and the WIRES-X software has not been established, so
check the cable connection and USB driver installation.
• To cancel the connection, press and hold the [
D X
] key.
2 & 0
Ჸ Ჸ
᲼ ᲻ ᲻ ᳀ Ჾ Ჸ
Ჽ Ჸ Ჸ 6 1 - ; 1 Ჺ ᲻
/ 76' 5%12' / 8 5 3 .
2. When the operation of the portable node is started, the “ X ” icon changes from blinking
to lit and the Node ID and the city of its own station are displayed.
Depending on the history of the previously connected node on the Internet and the
current connection status of the portable node, one of the following three screens is
displayed.
If the portable node is not connected to a node or a room on the Internet
① When connection history is not stored
The lower connection destination display will be blank.
Ჸ Ჸ
/ 76' 5%12' / 8 5 3 .
; # ' 5 7 6 5 7 4 +
5*+0#)#9#-7 , 3 ; $ ( 6 +
᲻
+ & 6 4 :
② When connection history is stored
The ID of the previous connected Node or Room will display in gray.
Press the PTT switch or touch [ connection ID ] to connect.
Upon being connected, the text will light up in white.
Ჸ Ჸ
/ 76' 5%12' / 8 5 3 .
; # ' 5 7 6 5 7 4 +
5*+0#)#9#-7 , 3 ; $ ( 6 +
᲻ ; # ' 5 7 6 7 4 +
+ & 6 4 :
If the portable node is already connected to a node or a room on the Internet
③
When connected to the same node or room as the ID of the previous connection history
The current connection ID is displayed in white. To communicate with this con-
nection, proceed to “ Communicating with other station ” (page 46).
If the current connection destination is different from the previous connection ID,
turning the DIAL knob displays the previous connection ID in gray. When the PTT
switch is pressed or [connection ID] is touched, the node will connect [
connection
ID ] is touched, the node will connect to the previous connection destination.
4 3 0 8  
M UTE SCOPE M / V S Q L
Y A E S U - T S U R I
SHINAGAWA-KU J Q 1 Y B F - T I
 Y A E S U - T U R I
I D : T 0 0 / R X 0 0

4 3 0 8  
M UTE SCOPE M / V S Q L
Y A E S U - T S U R I
SHINAGAWA-KU J Q 1 Y B F - T I
 Y A E S U - D R I V E
I D : T 0 0 / R X 0 0
While operating the Portable Node, it may be not possible to switch between “ Access Point ” and “ Direct Operation ”.
Press and hold the [ D X ] key to return to the transceiver setting screen, then press the B-Band DIAL knob.