Xirrus XR-1220 Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 200

background image

Wireless Array

Configuring the Wireless Array

159

The LED will still light during the boot sequence, then turn off. This
option is only available for the Gigabit interfaces.

3.

Allow Management on Interface

: Choose

Yes

to allow management of

this Array via the selected network interface, or choose

No

to deny all

management privileges for this interface.

4.

Auto Negotiate

: This feature allows the Array to negotiate the best

transmission rates automatically. Choose

Yes

to enable this feature, or

choose

No

to disable this feature — the default is enabled. If you disable

the Auto Negotiate feature, you must define the Duplex and Speed
options manually (otherwise these options are not available).

a.

Duplex

: Full-duplex mode transmits data in two directions

simultaneously (for example, a telephone is a full-duplex device
because both parties can talk and be heard at the same time). Half-
duplex allows data transmission in one direction at a time only (for
example, a walkie-talkie is a half-duplex device). If the Auto-
Negotiate feature is disabled, you can manually choose

Half

or

Full

duplex for your data transmission preference.

b.

MTU

: the Maximum Transmission Unit size. This is the largest packet

size (in bytes) that the interface can pass along.

c.

Speed

: If the Auto-Negotiate feature is disabled, you must manually

choose the desired data transmission speed from the pull-down list.
For configuring the Gigabit interfaces the options are

10 Megabit

or

100 Megabit

. (Note that 1000 Megabit speed can only be set by Auto-

Negotiation.)

5.

Configuration Server Protocol / IP Settings

: Choose

DHCP

to instruct

the Array to use

DHCP

when assigning IP addresses to the Array, or

choose

Static IP

if you intend to enter IP addresses manually. If you select

the Static IP option you must specify the IP address, IP subnet mask and
default gateway.

a.

Address

: If you selected the Static IP option, enter a valid IP address

for the Array. To use any of the remote connections (Web,

SNMP

, or

SSH), a valid IP address must be established.

«
...
177
178
179
180
181
...
»

Содержание XR-1220









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XR-1220

Бренд: D-Link Страницы: 166

Бренд: AirM2M Страницы: 64

Бренд: Planet Страницы: 42

Бренд: Jade Страницы: 7

Бренд: HiTi Digital Страницы: 26

Бренд: AirLive Страницы: 46

NUCLIAS CONNECT DAP-2680

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 25

Бренд: D-Link Страницы: 26

nuclias connect DAP-2662

Бренд: D-Link Страницы: 12

Nuclias Connect DAP-2622

Бренд: D-Link Страницы: 86

Бренд: D-Link Страницы: 18

Nuclias Connect DAP-2622

Бренд: D-Link Страницы: 8

Nuclias DBA-2520P

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды