Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 33

Страница: 33 / 199

Phaser 2135 Color Printer

E14

Close Duplex Unit, Duplex Unit Not Detected

E14-Duplex Unit Not
Detected

Ensure the duplexer is installed correctly.

Inspect the connector at the rear end of the
duplexer unit.

Inspect the wiring harness leading from the
duplexer unit interface connector to the
engine controller board.

Replace the duplexer unit.

Replace the engine controller board.

E18

Right Door A Open, Close Right Door A

E18-Right Door A Open

E20

Right Door B Open, Close Right Door B

E20-Right Door B Open

E21

Right Door C Open, Close Right Door C

E21-Right Door C Open

E22

Right Door D Open, Close Right Door D

E22-Right Door D Open

E23

Right Door E Open, Close Right Door E

E23-Right Door E Open

Ensure the cover’s sensor flag operates
freely.

Test the output bin full sensor using the test
described in “Switch scan test” on page 63.

Inspect the sensor and its wiring harness.

Replace the engine controller board.

Black Imaging Drum Missing, Reseat Drum

EA-Black Imaging Drum
Missing

Cyan Imaging Drum Missing, Reseat Drum

EA-Cyan Imaging Drum
Missing

Magenta Imaging Drum Missing, Reseat Drum EA-Magenta Imaging Drum

Missing

Yellow Imaging Drum Missing, Reseat Drum

EA-Yellow Imaging Drum
Missing

Remove and install the drum unit.

Inspect the spring-loaded drum contact assembly. Ensure they are clean
and move up and down freely. Remove the assembly and reseat it, if
necessary.

Replace the engine controller board.

Replace the printer unit chassis

Printer fault messages

Code

Front panel message

Service message

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды