Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 83

Страница: 83 / 199

Phaser 2135 Color Printer

Motor and clutch test constraints

Motor or clutch displayed
on control panel

Constraints
displayed on
control panel

Details

BLACK-ID MOTOR

REMOVE ID

Run test with the drum units removed.

Observe the imaging drum drive gear rotate

YELLOW-ID MOTOR

REMOVE ID

Run test with the drum units removed.

Observe the imaging drum drive gear rotate

MAGENTA-ID MOTOR

REMOVE ID

Run test with the drum units removed.

Observe the imaging drum drive gear rotate

CYAN-ID MOTOR

REMOVE ID

Run test with the drum units removed.

Observe the imaging drum drive gear rotate

TRANSFER BELT MOTOR

REMOVE ID

Run test with the drum units removed.

FUSER MOTOR

none

Remove the fuser and observe the fuser
drive gears turn.

REGISTRATION MOTOR

Remove media
from the
multi-sheet bypass
feeder

Remove the imaging drums and observe
the registration roller B rotate

REGISTRATION CLUTCH

none

Open the front cover and observe
registration roller A turning

FRONT MOTOR
(REGISTRATION MOTOR)

Remove media
from the
multi-sheet bypass
feeder

Open the multi-sheet bypass feeder and
observe the paper position plate cycle up
and down

REGISTRATION SHUTTER

none

Remove the imaging drums and the
transfer belt to watch the shutter open
and close smoothly and completely.

EXIT SOLENOID

none

Open the top cover and observe the exit
gate move up and down

FACEDOWN SOLENOID

none

Open the face-up tray and observe the
facedown gate move up and down

DUPLEX MOTOR

none

Listen for the motor turning for about 5
seconds

DUPLEX REAR CLUTCH

none

Listen for the clutch activating

DUPLEX FRONT CLUTCH

none

Listen for the clutch activating

TRAY 1 MOTOR
(FEED MOTOR)

EXIT TRAY1
CASSETTE

Run the test with Tray 1 removed.
Observe the pick roller rotate as the
motor runs

TRAY 2 MOTOR
(FEED MOTOR)

EXIT TRAY2
CASSETTE

Run the test with Tray 2 removed.
Observe the pick roller rotate as the
motor runs

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды