Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 137

Страница: 137 / 199

124

Phaser 2135 Color Printer

Transfer belt unit

Warning

Switch off the power and disconnect the power cord.

Open the top cover.

Remove the drum unit caddy. Cover the drum units and store in a safe
place.

Push the transfer belt unit locking tabs toward the left side of the
printer to release the unit.

Using the transfer belt unit handle, lift the unit about 1/2 inch (12 mm).

Using the handle and the front frame of the transfer belt unit, remove
the unit.

Reverse these steps to install the transfer belt unit. Ensure the transfer belt unit’s
locking tabs fully engage.

Removing the transfer belt unit

0725-35

Push Back
Locking Tabs

Lift
Transfer Belt Unit

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды