manualshive.com logo in svg

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Поделиться
Скачать
Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 152

Service Guide

139

Stack full sensor

Warning

Switch off the power and disconnect the power cord.

1.

Open the top cover.  Remove the drum/toner cartridges.  Place them in  
a lightproof black bag to protect the drum units from light and store in a 
safe place.

1.

Remove the top cover.

2.

Disconnect the four LED assembly power harnesses from the underside 
of the toner sensor board. 

3.

Close the top cover inner unit.

4.

Remove the four screws securing the metal shield over the toner 
cartridge sensor board.

5.

Remove the three screws securing the toner sensor board.

6.

Rotate the board up to expose the component side of the board.

7.

Disconnect the sensor’s connector from the toner sensor board.

8.

Free the disconnected cable from all cable retainers.

9.

Release the four locking tabs securing the stack full sensor, and remove 
the sensor.

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды