Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 156

Страница: 156 / 199

Service Guide

143

Fuser motor and transfer belt drive motor assembly

Warning

Switch off the power and disconnect the power cord.

Remove the print unit chassis as detailed in “Printer unit chassis” on
page 100.

Remove the rear fuser latching handle as described in “Fuser latching
handle (rear)” on page 134.

Disconnect the two inline connector leading to the fuser motor and belt
drive motor assembly.

Remove the two screws securing the fuser motor and belt drive motor
assembly to the printer frame.

Remove the motor assembly.

Reverse these steps to install the fuser motor. Ensure the wiring harnesses are
correctly routed through the restraints. Refer to “Wiring Diagram” on page 177.

Removing the fuser motor and transfer belt drive motor assembly

0725 48

Disconnect
Harness

Fuser Motor
and Transfer Belt Drive
Motor Assembly

Remove
Screws

Ensure wiring
harnesses are
correctly routed
and tie-wrapped
thru the restraint
posts

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды