Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 41

Страница: 41 / 199

Phaser 2135 Color Printer

These are error codes returned by the system controller board. In the event that
one of these errors occurs:

Cycle printer power to see if the error reoccurs.

Reseat the system controller board.

Replace the system controller board.

These errors can also be caused by the board’s hard drive or the RAM DIMMs.

System controller board fatal error codes

Code

Description

Unknown. Replace the hard drive before replacing the controller board.

Video Task

Serial Task

System Display Task

System Status Task

Startup, Key Press Processing, Menus Task

Parallel Port Read Buffer Manager

Parallel Port Write Buffer Manager

NVEE Manager

Scheduler

Job Log

Print File Task

Video Cleanup Task

Collation Task

Parallel Port Hear Task

PostScript Task 1. Replace the hard drive before replacing the controller
board.

PostScript Task 2

PostScript_Wrapper Task

PCL Task. Replace the hard drive before replacing the controller board.

PJL Task

Dequeue Task

In-menu Print File Task

Alert Recovery Task

Sweeper Task

SNMP Alert Task

SNMP Main Task

SNMP UDP Task

SNMP DDP Task

SNMP IPX Task

Notification Manager

Image Handler

Job Manager

PowerSaver Task

TIFF Task

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды