manualshive.com logo in svg

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Поделиться
Скачать
Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 12

 

Service Guide

 

xi

 

Removing the tray 1 entrance sensor actuator   121
Removing the belt entrance sensor actuator   122
Removing the duplex solenoid and the exit solenoid   123
Removing the transfer belt unit   124
Removing the registration clutch   125
Removing the registration motor assembly   126
Removing the registration roller assembly A and drive gear   128
Removing the registration roller assembly B   129
Removing the duplex guide assembly   131
Fuser latching handle (left)   133
Fuser latching handle (left)   134
Removing the fuser exit roller   136
Removing the exit sensor assembly   137
Removing the eject guide assembly   138
Removing the stack full sensor   140
Removing the main motor assembly   142
Removing the fuser motor and transfer belt drive motor assembly   143
Removing the shutter plate   144
Removing the color registration sensor assembly   145
Removing the color registration solenoid   146
Removing an LED assembly   147
Removing the drum contact assembly   148
Removing the toner sensor actuators   150
Removing the duplex unit   151
Cabinet and top cover FRUs   155
Top cover FRUs   157
Printer chassis FRUs (1 of 2)   159
Printer chassis FRUs (2 of 2)   161
Paper tray and paper tray guides FRUs   163
Electrical components FRUs   164
Duplexer unit   165
Lower Tray Assembly FRUs   167
Wiring diagram   177
Wire routing at the engine controller board   178
Details of wiring passthru   179
Wiring under the top shield plate   180
Wiring harnesses route by the imaging drum motors   181
Wire routing by the fuser and transfer belt motor unit.   181
Ribbon cable routing under the toner sensor board   182

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды