manualshive.com logo in svg

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию, Страница: 139 / 199

Поделиться
Скачать
Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 139

126

Phaser 2135 Color Printer

Registration motor assembly

Warning

Switch off the power and disconnect the power cord.

1.

Open the top cover.  Remove the drum/toner cartridges.  Place them in  
a lightproof black bag to protect the drum units from light and store in a 
safe place.

2.

Open the front cover.

3.

Remove the rear shield plate as described in the topic “Rear shield 
plate” on page 97.

4.

Remove the registration clutch as detailed in “Registration clutch” on 
page 125.  

5.

Remove the screws securing the motor bracket to the printer.

6.

Remove the registration motor assembly.

7.

Disconnect the harness from the registration motor.  

8.

If replacing the motor, remove the two screws securing the motor to the 
motor bracket.

Reverse these steps to install the registration motor assembly.  

Removing the registration motor assembly

0725-37

Registration Motor

Ground Plate

Remove
Screws

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Отзывы:

Нет отзывов