Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 36

Страница: 36 / 199

Service Guide

Fuser Upper Error T1 Power Off/On

T1-Fuser Upper Error

Fuser Lower Error T2 Power Off/On

T2-Fuser Lower error

1. Remove and install the fuser.
2. Test the thermistors inside the fuser using the test described in “Switch

scan test” on page 63.

3. Replace the fuser.
4. Replace the low-voltage power supply.
5. Replace the engine controller board.

T29

Temp Sensor Error T29, Power Off/On

T29-Temp Sensor Error

T30

RH Sensor Error T30, Power Off/On

T30-RH Sensor Error

1. Test the temperature sensor or the relative humidity sensor using the

sensor test described in “Switch scan test” on page 63.

2. Inspect the wiring harness leading to the entrance sensor board.
3. Replace the temperature/humidity sensor board.
4. Replace the engine controller board.

T31

Roller Over Temp T31, Power Off/On

T31-Roller Over Error

1. Inspect the fuser cooling fan. Ensure it is running correctly and is not

blocked.

2. Remove and install the fuser.
3. Test the thermistor inside the fuser using the test described in “Switch scan

test” on page 63.

4. Replace the fuser.
5. Replace the low-voltage power supply.
6. Replace the engine controller board.

T32

LED Over Temperature T32, Power Off/On

T32-LED Over Temp Error

1. Ensure all the chassis cooling fan is operating and is not blocked.
2. Ensure the printer is operating in the correct temperature environment; the

printer’s Service Menu : Print Diag Summary test page lists the ambient
temperature sensed by the printer.

3. Replace the LED heads.
4. Replace the engine controller board.

Printer fault messages

Code

Front panel message

Service message

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Бренды по названию

Популярные бренды