Xerox 2135DX - Phaser Color Laser Printer Скачать руководство пользователя страница 82

Страница: 82 / 199

Service Guide

Motor and clutch tests

Enter the diagnosis mode by pressing and holding the

Menu (1)

and

Enter (4)

keys as you turn on the printer.

Press the

Menu (1, 5)

keys to scroll through the list of test until

MOTOR

& CLUTCH TEST

appears on the upper display.

Caution

Before running some motor and clutch tests you must remove
certain printer consumable items; refer to table below. The front
panel also reminds you to remove the necessary item before
starting the test.

Press the

Item (2, 6)

keys to scroll through the list of motors and

clutches until the desired item is displayed.

If indicated, remove the consumable items constraining the test.

Press the

Value (3)

key to start the displayed test. The displayed test

item blinks, and the selected motor or clutch is driven for 10 seconds.

Press the

Value (7)

key to stop the unit.

Repeat the Steps 2 to 7 for other motor or clutch tests.

Press Enter (4) ends the tests.

Содержание 2135DX - Phaser Color Laser Printer








































































































































































































Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды

Xerox 2135DX - Phaser Color Laser Printer, Руководство по обслуживанию

Результаты поиска

Содержание 2135DX - Phaser Color Laser Printer

Отзывы:

Похожие инструкции для 2135DX - Phaser Color Laser Printer

Бренды по названию

Популярные бренды